News

News

Nanotechnology Enables Engineers to Weld Previously Un-weldable Aluminum Alloy

Data: 2019-02-13
Views: 120

IMAGE: THESE ARE TWO PIECES OF ALUMINUM ALLOY 7075 WELDED TOGETHER USING A NANOPARTICLE-ENHANCED FILLER WIRE. 

CREDIT: UCLA SAMUELI ENGINEERING


An aluminum alloy developed in the 1940s has long held promise for use in automobile manufacturing, except for one key obstacle. Although it's nearly as strong as steel and just one-third the weight, it is almost impossible to weld together using the technique commonly used to assemble body panels or engine parts.

That's because when the alloy is heated during welding, its molecular structure creates an uneven flow of its constituent elements -- aluminum, zinc, magnesium and copper -- which results in cracks along the weld.

Now, engineers at the UCLA Samueli School of Engineering have developed a way to weld the alloy, known as AA 7075. The solution: infusing titanium carbide nanoparticles -- particles so small that they're measured in units equal to one billionth of a meter -- into AA 7075 welding wires, which are used as the filler material between the pieces being joined. 

Using the new approach, the researchers produced welded joints with a tensile strength up to 392 megapascals. (By comparison, an aluminum alloy known as AA 6061 that is widely used in aircraft and automobile parts, has a tensile strength of 186 megapascals in welded joints.) And according to the study, post-welding heat treatments, could further increase the strength of AA 7075 joints, up to 551 megapascals, which is comparable to steel.

Because it's strong but light, AA 7075 can help increase a vehicle's fuel and battery efficiency, so it's already often used to form airplane fuselages and wings, where the material is generally joined by bolts or rivets rather than welded. The alloy also has been used for products that don't require joining, such as smartphone frames and rock-climbing carabiners.

But the alloy's resistance to welding, specifically, to the type of welding used in automobile manufacturing, has prevented it from being widely adopted.

'The new technique is just a simple twist, but it could allow widespread use of this high-strength aluminum alloy in mass-produced products like cars or bicycles, where parts are often assembled together,' said Xiaochun Li, UCLA's Raytheon Professor of Manufacturing and the study's principal investigator. 'Companies could use the same processes and equipment they already have to incorporate this super-strong aluminum alloy into their manufacturing processes, and their products could be lighter and more energy efficient, while still retaining their strength.'

The researchers already are working with a bicycle manufacturer on prototype bike frames that would use the alloy; and the new study suggests that nanoparticle-infused filler wires could also make it easier to join other hard-to-weld metals and metal alloys.


via: https://www.eurekalert.org


News / Recommended news More
2019 - 11 - 11
India's October finished steel exports surged by 60pc to 950,000t from a year ago, according to initial estimates by the Indian steel ministry.Year-to-date exports have risen by 27.7pc to 4.88mn t for April-October from the same period in 2018. India's fiscal year runs from 1 April.A surge in hot-rolled coil (HRC) exports is driving much of the growth.Indian mills are competing aggressively with A...
2019 - 11 - 07
Scientists from the National University of Science and Technology MISiS have created new aluminium alloys that are cheap and effective to use in a wide variety of modern vehicles.Aluminium and its alloys rank second after iron alloys in terms of scalability. Aluminium is easily processed by forging, stamping and rolling; it is also characterised by low density, and aluminium products are lightweig...
2019 - 10 - 30
A team of the TSU Laboratory of High-Strength Crystal Physics is creating highly entropic alloys that differ in the unusual structure of the crystal lattice. They provide new materials with mechanical characteristics that make them suitable for use in the extreme conditions of space and the Arctic – at high and low temperatures, under load, and when exposed to radiation.The object of the physicist...
2019 - 10 - 25
To reduce the manufacturing costs of making tungsten carbide tools, a team of researchers at the U.S. Army Research Laboratory has figured out how to 3D print it into the exact size and shape they want, with little to no post-machining required, according to a U.S. patent application first made public on Thursday.Tungsten carbide is hard, so hard that it’s expensive to make it into useful tools an...
Share:
Uniris Exhibition Shanghai Co., Ltd.
Shanghai Branch
Tel:4000 778 909
E-mail:irisexpo@163.com
  
Guangzhou Branch
Tel:020-8327 6389
E-mail:pmchina@unifair.com

CCEC CHINA official website
犀牛云提供企业云服务
Scan the QR code to visit the official website by phone